铝板深加工，你知道多少呢?相信很多人和小编一样是个小白吧!没有关系，让我们跟着铝板生产厂家一起来看看吧
How much do you know about deep processing of aluminum plate? I believe many people are just like Xiaobian! It doesn't matter. Let's take a look with the aluminum plate manufacturer
铝板深加工的步骤如下：
The steps of deep processing of aluminum plate are as follows:
选板：我们须要选择那些合金铝板硬度不高，不易弯曲断裂的，所以，在原材料上面须选用铝板。
Plate selection: we need to select those alloy aluminum plates with low hardness and not easy to bend and fracture. Therefore, aluminum plates must be selected for raw materials.
在运输和加工过程中的保护：根据客户的要求，将原材料粘贴在一侧(光滑表面)或两侧，以避免运输或加工过程中损坏零件表面。
Protection during transportation and processing: according to the customer's requirements, the raw materials are pasted on one side (smooth surface) or both sides to avoid damage to the part surface during transportation or processing.
零件的表面冲裁：零件的冲裁和冲裁，在送料和冲裁前应调整上下模间隙。
Surface blanking of parts: for blanking and blanking of parts, the clearance between upper and lower dies shall be adjusted before feeding and blanking.
弯曲：为了尽量减少对板材内部结构的损坏，应增加弯曲角度，以满足产品的使用条件;弯曲方向应垂直于铝板的纹理方向。
Bending: in order to minimize the damage to the internal structure of the plate, the bending angle should be increased to meet the service conditions of the product; The bending direction shall be perpendicular to the grain direction of the aluminum plate.

之后是焊接：根据板料厚度和材料性能，选择相应的焊丝和焊接类型，调整相应的电压范围、电流范围和气压范围。
Then welding: according to the sheet thickness and material properties, select the corresponding welding wire and welding type, and adjust the corresponding voltage range, current range and gas pressure range.
铝板的深加工也要注意零件表面的冲压问题。在铝板切割和冲压机之前，须调整数控刀片左右模具的间隙。与普通冷轧钢板相比，铝板之间的间隙应该减少，以防止冲压伤口的毛刺过大。
In the deep processing of aluminum plate, attention should also be paid to the stamping of the part surface. Before the aluminum plate cutting and stamping machine, the clearance between the left and right dies of the NC blade must be adjusted. Compared with ordinary cold-rolled steel plate, the gap between aluminum plates should be reduced to prevent excessive burr of punching wound.
铝板深加工也要注意铝板加工过程中的弯曲，其弯曲标准是在达到商品应用标准的情况下，能尽可能地增加弯曲的内角，这样可以防止板材内部机构的损坏，但须注意的是，铝板的弯曲方向须是垂直的，不能是平行的。
In the deep processing of aluminum plate, attention should also be paid to the bending during the processing of aluminum plate. The bending standard is to increase the internal angle of bending as much as possible when the commercial application standard is met, so as to prevent damage to the internal mechanism of the plate. However, it should be noted that the bending direction of aluminum plate must be vertical and not parallel.
关于铝板深加工的相关步骤以及它的注意事项就到这里了，如果您有疑惑就来我们网站//www.renttoplux.com联系吧，有关人员为您解惑答疑。
That's all about the steps and precautions of aluminum plate deep processing. If you have any questions, please come to our website //www.renttoplux.com Contact us and relevant personnel will answer your questions.