铝板在生产过程中往往会有很多问题，铝板生产中为常见的问题不外乎表面问题、板型问题、轧制厚度问题。所以生产人员在铝板生产中要时刻的关注以上几个要点，下面铝板生产厂家来讲讲吧。
There are often many problems in the production process of aluminum plates. The common problems in aluminum plate production are nothing more than surface problems, plate shape problems, and rolling thickness problems. Therefore, the production personnel should always pay attention to the above points in the aluminum plate production. Let's talk about it from the aluminum plate manufacturer.
铝板生产中的表面问题：
Surface problems in aluminum plate production:
表面问题主要为擦划伤、黄油斑问题，铝板在生产过程中如果机台上面有金属颗粒那么会在生产过程中出现纹理一直的擦划伤，生产人员需要立即停机清理机台。黄油斑问题是由于轧制油没有及时更换或者是轧制设备的吹风系统出现故障导致的，虽然后期可通过铝板拉弯矫清洗进行处理，但是生产人员还是需要注意黄油斑，如果对于高要求的外观件对于黄油斑都是视为不合格的铝板。
The surface problems are mainly scratches and grease stains. If there are metal particles on the machine table during the production process, the aluminum plate will be scratched all the time during the production process. The production personnel need to stop the machine immediately to clean the machine table. The problem of grease stain is caused by the rolling oil not being replaced in time or the failure of the air blowing system of the rolling equipment. Although it can be handled through the aluminum plate stretching, bending, straightening and cleaning in the later stage, the production personnel still need to pay attention to the yellow oil stain. If the parts with high requirements for appearance are regarded as unqualified aluminum plates for the grease stain.
铝板生产中的板型问题：
Plate type problems in aluminum plate production:
板型问题一直是比较难以控制的，主要和轧机轧辊有关系，轧机如果在长期轧制过程中没有及时修复轧辊磨损的间隙则会出现板型波浪问题，中浪和边浪都可能会产生。波浪板型问题已经发现生产人员需要立即向生产主任反馈，排除是否因为轧机压力不均匀还是其它原因，如果是轧辊磨损严重需要更换轧辊。
The plate shape problem is always difficult to control, which is mainly related to the rolling mill roll. If the rolling mill fails to repair the gap of the roll wear in a timely manner during the long-term rolling process, the plate shape wave problem will occur, and the middle wave and side wave may occur. The problem of wavy plate shape has been found that the production personnel need to report it to the production director immediately to rule out whether it is due to uneven rolling mill pressure or other reasons. If the roll is seriously worn, it needs to be replaced.

铝板生产中的厚度问题：
Thickness problem in aluminum plate production:
还是和轧机有关系，轧机压力不均匀导致，目前轧机都有在线测量设备，该问题已经不再经常出现。
It is still related to the rolling mill, which is caused by uneven rolling mill pressure. At present, the rolling mill has online measuring equipment, and this problem no longer occurs frequently.
铝板硬度问题：
Hardness of aluminum plate:
主要和退火时间有关系，很多时候由于退火时间不足导致力学性能不达标，比如半硬状态的铝板出现折弯开裂，或者拉伸铝板出现拉伸开裂均是铝板硬度不达标，主要需要检查退火设备的温度、退火时间。
It is mainly related to the annealing time. In many cases, the mechanical properties are not up to the standard due to insufficient annealing time. For example, bending cracks occur on semi hard aluminum plates, or tensile cracks occur on stretched aluminum plates. The hardness of aluminum plates is not up to the standard. It is mainly necessary to check the temperature and annealing time of the annealing equipment.
生产车间的人员需要在生产中及时发现问题，同时及时纠正问题，避免铝板出现质量不合格，提高铝板的成品率和良品率。更多相关事项就来我们网站//www.renttoplux.com进行咨询吧！
The personnel in the production workshop need to find problems in time during production and correct them in time to avoid unqualified aluminum plates and improve the yield and yield of aluminum plates. Come to our website for more information //www.renttoplux.com Consult!